Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 11:52, 20 March 2025 24.130.110.112 talk posted a new comment on X1200 (I have the battery low voltage set to 4V and if I watch it in bat.py it works as expected and shuts down when it drops below that. But if I'm on another screen and wait it drops below 4 without shutting down. It then shuts down as soon as I run bat.py)
  • 11:23, 20 March 2025 Lisa talk contribs posted a new comment on X306 (Hi,X306 does not have a RTC function.)
  • 22:38, 19 March 2025 85.73.34.174 talk posted a new comment on X306 (I don’t see an RTC, which is important for small projects. Are there any plans for a version of the X306 with an RTC?)
  • 17:23, 19 March 2025 62.176.175.178 talk posted a new comment on X1009 (Okay, so only the barrel jack)
  • 12:07, 19 March 2025 Lisa talk contribs posted a new comment on X1001 (Hello,friend：it depends on the Raspberry Pi 5,does not depend on the X1001 board,X1001 just provides an PCIe interface for the SSD and RP5, hope to get your understanding.)
  • 12:01, 19 March 2025 Lisa talk contribs posted a new comment on X1009 (You can power the HDD separately, but it does not support powering the X1009 HAT from the HDDs.)
  • 03:55, 19 March 2025 77.23.255.54 talk posted a new comment on X1009 (I bought a defect X1009 SATA Shield and they refunded my money. But they refuse to allow me to purchase it again. :( So if your X1009 SATA Shield works its fine. But if not you will not get any support.)
  • 02:57, 19 March 2025 103.21.165.149 talk posted a new comment on X1001 (Does X1001 support arm64 Ubuntu 2024 Desktop version?)
  • 21:27, 18 March 2025 62.176.175.178 talk posted a new comment on X1009 (Dear Lisa and Harry, as mentioned earlier, i am powering my HDDs with Corsair 850 W ATX PSU. That is fine, now, i would like to use 5 V output from Corsair to power Raspi to sort of offload onboard (on the SATA hat) 12 V to 5 V regulator. Can i feed 5 V from Corsair to the hat via the HDD connector? As You can imagine, Corsair has plenty of power for my Raspi and this way i would like to derease heat produced by the hat... thanks)
  • 14:28, 18 March 2025 Lisa talk contribs deleted comment #5674 on X1200
  • 14:28, 18 March 2025 Lisa talk contribs posted a new comment on X1200 (Hello，you can change the battery low voltage to implement safe shutdown. default is less than 3.20Vdc. [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software])
  • 14:28, 18 March 2025 Lisa talk contribs deleted comment #5675 on X1200
  • 14:28, 18 March 2025 Lisa talk contribs posted a new comment on X1200 ([https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software] [https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software])
  • 14:28, 18 March 2025 Lisa talk contribs posted a new comment on X1200 (Hello，you can change the battery low voltage to implement safe shutdown. default is less than 3.20Vdc.[https://suptronics.com/Raspberrypi/Power_mgmt/x120x-v1.0_software.html X1200 Software])
  • 11:01, 18 March 2025 24.130.110.112 talk posted a new comment on X1200 (Hello I'm not getting the expected behavior. When not charging it doesn't automatically shut down when the voltage drops below the specified number. But when I then use sudo python3 bat.py in terminal it immediately recognizes voltage is low and initiates shutdown. How do I make it work without having to manually check the voltage?)
  • 10:40, 18 March 2025 Lisa talk contribs posted a new comment on T201 (Hi,We have received your email feedback and have replied to you via email.)
  • 17:31, 17 March 2025 103.217.176.215 talk posted a new comment on T201 (Hi, I hope you are doing well. We bought more than 40 pieces of these UPS and facing power issues. I am reaching out for your assistance in troubleshooting an issue where my Jetson Nano turns ON without any input power supplied to the Geek T201 1-Cell 18650 UPS. This issue consistently occurs after a day or two. During my investigation, I conducted tests under the following conditions: No connection was made to Pins 1 and 2 of the AL ON header. No connection was made to Pins 3 and 4 of th...)
  • 11:50, 17 March 2025 Lisa talk contribs posted a new comment on X1001 (Hi,Sorry, WD Blue SN580 is not compatible at the moment. We recommend you use a compatible SSD for testing.)
  • 11:48, 17 March 2025 Lisa talk contribs posted a new comment on X1001 (Hi,What type of SSD are you using? [WD Black SN850 series] [WD Black SN770] has compatibility issues; please try changing the SSD to test it.)
  • 11:39, 17 March 2025 Lisa talk contribs posted a new comment on X1206 (Hello,please refer to FAQ ---[Q: Why does the message "This power supply is not capable of supplying 5A" appear??])
  • 21:50, 16 March 2025 45.12.25.232 talk posted a new comment on X1206 (Hello! I've attached my Raspberry Pi to the x1206 UPS hat and ensured proper contact for all pins. Inserted four 21700 batteries properly oriented (+to+, -to-). Connected monitor/mouse/keyboard. Tried to power UPS via DC power jack using Geekworm recommended power supply. Also tried to power UPS via USB-C power input (the one on UPS board, not the one on Raspberry PI board) using official Raspberry Pi 5 power supply. In both cases - Raspberry Pi booted successfully. But it showed a notif...)
  • 18:34, 16 March 2025 175.116.49.141 talk posted a new comment on X1001 (The WD Blue SN580 series is known to have compatibility issues. Could you suggest any possible solutions to resolve this problem?)
  • 00:55, 16 March 2025 172.56.70.37 talk posted a new comment on X1001 (Anonymous user #41 here. I forgot to mention that I am using a WD Black that has SanDisk chips, not Phison controller...)
  • 09:22, 15 March 2025 172.56.70.37 talk posted a new comment on X1001 (X1001 will not boot NVME 1Tb. 1Tb drive boots fine with USB3 adapter. Tried boot config changes, and eeprom changes suggested. 'Failed to open device nvme' Since no SD card, not sure if X1001 is actually working...)
  • 16:19, 14 March 2025 104.28.54.42 talk posted a new comment on XScript (Found it. The problem is, the misusing of wire color. Typically a fan with pwm control has a blue wire. Geekworm controlled the fan by PWM, but has a yellow wire. The yellow wire is used for tachometer/RPM control. In my case, i connected the blue fan wire to the yellow geekworm connector and it works.)
  • 10:47, 14 March 2025 Lisa talk contribs posted a new comment on KVM-A8 (Hello，KVM-A8 does not support V4, please download V3 for testing.)
  • 04:13, 14 March 2025 90.152.206.118 talk posted a new comment on KVM-A8 (I bought the KVM-A8-PCI two days ago. I tried to install it according to the instructions. Unfortunately, the two-year-old YouTube instructions no longer match the PIKVM website, and after several attempts, I can't get the RPI v4 to load the operating system. Which version should I actually use?)
  • 16:46, 13 March 2025 62.176.175.178 talk posted a new comment on X1009 (Dear all, despite the fact i wanted to use latest ubuntu image on my Raspi, i tried latest Raspi image without desktop and everything works like charm. I did not even had to enable pci port:) I will put the Ubuntu card in and make video hopefully next week or so. Many thanks.)
  • 11:44, 13 March 2025 Harry talk contribs posted a new comment on X1009 (To determine whether it is caused by the power supply or the system, can you provide a detailed video to describe the problem? You can email to us.)
  • 11:42, 13 March 2025 Lisa talk contribs posted a new comment on X1009 (Thanks for the information. Could you please send a test video via email [support@geekworm.com]? It would be easier to identify the problem with a test video.and please let us known the order NO.)
  • 11:16, 13 March 2025 Lisa talk contribs posted a new comment on X1202 (Hello,It is recommended that you perform a complete charging and discharging process on the battery. After a full charge, remove the power source and charge the battery after it is fully discharged. Train the UPS to memorize the charging and discharging process.)
  • 00:52, 13 March 2025 62.19.102.192 talk posted a new comment on X1202 (Hello, I installed the board on a Raspberry Pi 5 (8GB), but it doesn't work properly. When I disconnect the power supply, the state change is detected only after several minutes, and the battery percentage continues to increase. Similarly, when the status finally changes and I reconnect the power, the battery percentage keeps dropping. What am I doing wrong? Is there a firmware update available? At the hardware level, the LEDs seem to work correctly, both those indicating power status and bat...)
  • 18:24, 12 March 2025 62.176.175.178 talk posted a new comment on X1009 (HDDs are 5x Seagate Skyhawk ST4000VX016 PS: once booted, if i connect the fifth to shield, it is recognised:))
  • 18:16, 12 March 2025 62.176.175.178 talk posted a new comment on X1009 (Dear Lisa, i understand the power supply needs. Now i connected Corsair 850 W ATX PSU to disks. I have found out that if i connect all 5 HDDs to the shield, the Raspi would not boot. As long as i disconnect one (i tried first on port 0 and fifth on port 4), raspi boots like charm :))
  • 17:08, 12 March 2025 77.171.55.137 talk posted a new comment on X1200 (Thank you Lisa! I'll keep the battery size requirements in mind.)
  • 12:21, 12 March 2025 Lisa talk contribs posted a new comment on X1200 (Hi，You can use it, please refer to the battery size requirements to ensure that it can be installed, refer to X1200#FAQ---Q: What battery is recommended for this ups shield)
  • 12:17, 12 March 2025 Lisa talk contribs posted a new comment on X1001 Hardware (Hi!sorry,there is no CAD model.)
  • 12:12, 12 March 2025 Lisa talk contribs deleted comment #5649 on X1200
  • 12:11, 12 March 2025 Lisa talk contribs posted a new comment on X1200 (Did you do a power setup? please refer to the X1200#FAQ 【Q: Why does the message "This power supply is not capable of supplying 5A" appear??】 If the problem is still not solved, please contact us by email（with your order No）, and please send us some installation/test pictures. <support@geekworm.com>)
  • 12:08, 12 March 2025 Lisa talk contribs posted a new comment on X1200 (Did you do a power setup? please refer to the X1200#FAQ 【Q: Why does the message "This power supply is not capable of supplying 5A" appear??】)
  • 11:55, 12 March 2025 Lisa talk contribs posted a new comment on X1009 (You can choose the appropriate power supply according to your needs. 12Vdc +/-5% ≥5A for two 3.5" HDDs, ≥7A for three 3.5" HDDs, ≥9A for four 3.5" HDDs, ≥11A for five 3.5" HDDs 12Vdc +/-5% ≥4A for two 2.5" HDDs, ≥5A for three 2.5" HDDs, ≥6A for four 2.5" HDDs, ≥7A for five 2.5" HDDs Your SATA drives can also be powered from a separate PSU. You need to calculate the total current required for all the HDDs you are using. Check the HDD nameplate to get the HDD startup current (the startup cu...)
  • 03:32, 12 March 2025 91.127.238.207 talk posted a new comment on X1009 (Hi Lisa, i thought that the 5V regulator would not be able to supply 5 A to raspi and also 5 V to all five HDDs)
  • 02:14, 12 March 2025 185.247.141.21 talk posted a new comment on X1001 Hardware (Hi! Is there somewhere I can download the CAD model X1001? I need it to design the device.)
  • 21:08, 11 March 2025 24.23.117.54 talk posted a new comment on X1200 (I am using the white canakit 27W, 5A power supply. The Pi is on, on the front piece I am seeing green LED and a Solid red LED.) Tags: Mobile web edit, Mobile edit
  • 17:34, 11 March 2025 77.171.55.137 talk posted a new comment on X1200 (Hello Geekworm, For the X1200 can I also use Panasonic NCR18650BD (3180mAh - 10A) instead of Panasonic NCR18650B (3350mAh - 6.7A) ?? Thanks for the answer!)
  • 15:13, 11 March 2025 Lisa talk contribs posted a new comment on X652 (Hi,RTC does not require any configuration, please check if you downloaded PiKVM V3 platform OS, and V4 is not supported!)
  • 15:06, 11 March 2025 Lisa talk contribs posted a new comment on X1200 (Hello, What power supply are you using and what is the state of the led's on the x1200 board?)
  • 08:56, 11 March 2025 24.23.117.54 talk posted a new comment on X1200 (Hello, any idea why my raspbeery Pi 5 has a flashing red light after adding the hat to it?)
  • 08:46, 11 March 2025 180.15.97.233 talk posted a new comment on X652 (My X652 outputs RTC related error repeatedly via syslog. Dose PiKVM supports RTC on X652 ? 2025-03-11 Mar 11 09:30:18.860140 x652 daemon.info Started PiKVM - RTC-based hardware watchdog. 2025-03-11 Mar 11 09:30:19.362907 x652 daemon.info kvmd.apps.watchdog INFO --- Running watchdog loop on RTC0 ... 2025-03-11 Mar 11 09:30:19.362907 x652 daemon.info Traceback (most recent call last): 2025-03-11 Mar 11 09:30:19.362907 x652 daemon.info File "/usr/bin/kvmd-watchdog", line 8, in...)
  • 06:18, 8 March 2025 31.192.210.139 talk posted a new comment on X1002 (Hello again, When I couldn't get an answer from here, I sent an e-mail to your support e-mail address. They responded and requested some details. I shared all of them with all the details by replying to the e-mail just now. I wish you good work.)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"