Comments log

Jump to navigation Jump to search

This is a log of comments.

Logs
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
  • 05:44, 10 April 2020 80.98.41.181 talk posted a new comment on X850 (Hey, where could I buy the newest (and smallest) USB 3.0 - mSATA hat for my Pi4? I've found only the giant old one (with SATA) on your webshop. Thanks!)
  • 00:43, 10 April 2020 93.11.154.146 talk posted a new comment on RPI HIFI AMP (The 19v power supply is to weak for the rapsberry pi3. Is it possible to use a 19v powersupply for laptop with 4.65 A ?)
  • 18:39, 9 April 2020 Cindy talk contribs posted a new comment on Armor Case B (Hi, sorry, it must be related with some invidual thermal pads, you can thermal grease to replace it to get better dissaption.)
  • 05:12, 9 April 2020 217.96.169.155 talk posted a new comment on Armor Case B (SoC pillar is too tall for 1mm thermopad. Either cut it down 0.5mm or provide 0.5mm thermopads. Had to trim the pad in half otherwise rPi board was bowing.)
  • 11:47, 8 April 2020 Harry talk contribs posted a new comment on X705 (Please refer to X750)
  • 11:36, 8 April 2020 113.73.27.139 talk posted a new comment on X705 (Hi, The X750 has power-patch management to avoid battery frequent charging & discharging, and PI will be powered by power adapter once power adapter is connected. so the X750 is suitable for permanent connection. FYI, we will have a new model which called X728 has the same advanced power-patch management but also adds power loss detection, improved auto powering on, safe shutndown when battery low, RTC..etc.)
  • 02:42, 8 April 2020 GrahamO talk contribs posted a new comment on X705 (Is this device suitable for permanent connection to a 5V DC charging/power source to enable fail over to battery when the 5V source gets disconnected i.e. will it act a UPS when the main supply is disconnected. Does it have 'power path' management so that the Raspberry Pi only uses the main 5V supply and not the battery when the supply is connected?)
  • 17:06, 7 April 2020 Cindy talk contribs posted a new comment on X735 (Hi, maybe you can refer to here X856#Some_Tips to get some information.)
  • 02:35, 7 April 2020 84.65.200.167 talk posted a new comment on X835 (@Harry - ok so that doesn't seem practical, would an x735 board provide enough general cooling and then remove the case fan? thanks)
  • 17:08, 6 April 2020 Harry talk contribs posted a new comment on X835 (Hi, Please refer to: File:X835-latching-switch.jpg Regards, Harry / Geekworm)
  • 16:57, 6 April 2020 Harry talk contribs posted a new comment on X835 (1. x835 supports PI 3B+; 2. X835 is stackble, but the USB 3 cable is shorten, you need use the long USB 3 cable. Harry / Geekworm)
  • 23:38, 5 April 2020 65.130.195.127 talk posted a new comment on X735 (As other's have said the script doesn't seem like the best way to do this. Is there a better script to do this? This thing is eating up CPU.)
  • 00:45, 5 April 2020 84.65.200.167 talk posted a new comment on X835 (Using an x835 box and pressing the power button does not shut down the x835 board & fan. Should it? The Pi switches off but the fan is still spinning and the blue power light is on. No jumper was removed.)
  • 21:17, 4 April 2020 202.136.166.173 talk posted a new comment on X835 (I have 2 questions: 1)Does X835 support Raspiberry 3B+ ? 2)Is X835 stackable such as X828? I have a Pi 3B+ and two 3.5" Disks, and want to build a NAS. Thanks)
  • 15:48, 4 April 2020 Harry talk contribs deleted comment #871 on X872
  • 15:48, 4 April 2020 Harry talk contribs posted a new comment on X872 (test)
  • 11:55, 4 April 2020 Harry talk contribs deleted comment #870 on 测试页面
  • 11:55, 4 April 2020 Harry talk contribs posted a new comment on 测试页面 (test ~~~)
  • 11:55, 4 April 2020 Harry talk contribs deleted comment #869 on 测试页面
  • 11:55, 4 April 2020 Harry talk contribs posted a new comment on 测试页面 (test)
  • 17:12, 3 April 2020 Harry talk contribs posted a new comment on 2.2 LCD (Hi, Please refer to Ugeek LCD user manual, then select 'Reset RPi config to default' item. Harry / Geekworm)
  • 15:50, 3 April 2020 Cindy talk contribs posted a new comment on X750 (Hi, it is right, we just check again and do some update about the photo, please check: https://www.raspberrypiwiki.com/index.php/PH2.0_Conector_Specification)
  • 14:31, 3 April 2020 Cindy talk contribs posted a new comment on 2.2 LCD (Hi friend, For Pi 4 use, please refer to 2.4" LCD:https://www.raspberrypiwiki.com/index.php/2.4_LCD)
  • 11:11, 3 April 2020 14.201.36.12 talk posted a new comment on X750 (Are you sure that PH2.0 connector power switch connector specification link you provided is correct? I metered out the connections and found the switch was on pin 3, not pin 1 as per your specification, can you check and confirm you connections please.)
  • 16:49, 2 April 2020 132.166.183.104 talk posted a new comment on 2.2 LCD (Hi, great wiki. But how to remove all like as we never installed it ?)
  • 16:45, 2 April 2020 Cindy talk contribs posted a new comment on EXP GDC (Hi friend, Sorry, we can not guarantee the compatibility.You need to test it.)
  • 12:27, 2 April 2020 Cindy talk contribs posted a new comment on Armor Case B (Hi friend,please use M2.5x10mm screws.)
  • 05:59, 2 April 2020 190.16.183.220 talk posted a new comment on Armor Case B (I need the kit of screw. Can somebody tell me what kind of screw did I need? Thank you.)
  • 23:05, 31 March 2020 93.178.63.36 talk posted a new comment on EXP GDC (Hi Friends I have Lenovo y50 with GTX860m the question is what graphic card is compatible ?)
  • 15:51, 31 March 2020 Abby talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Sorry, it is not recommend to use with 4K TV as it may have some compability problem.)
  • 19:12, 30 March 2020 Cindy talk contribs posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (Hi, Yes, you can do a test.)
  • 19:11, 30 March 2020 Cindy talk contribs posted a new comment on Armor Case B (Hi, The two coolig fan size is 25x25x8mm.)
  • 19:06, 30 March 2020 95.123.191.114 talk posted a new comment on Armor Case B (Hi guys, what are the dimensions of the fans? Thank you!)
  • 18:35, 30 March 2020 Cindy talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Double 8 and singe 8 board are two different boards.)
  • 18:35, 30 March 2020 Cindy talk contribs posted a new comment on LVDS To HDMI Adapter Board (Hi, Sorry, not support cash on delivery.)
  • 11:51, 30 March 2020 Breton22 49 talk contribs posted a new comment on Auto Mount an NTFS USB Drive on Raspberry Pi (Hello. Can I use this procedure with 1 Raspberry PI 4B and 1 HDD 3.5 WD + X835?)
  • 09:09, 30 March 2020 Harry talk contribs posted a new comment on X750 (Hi,bill. Please refer to File:IP5310-datasheet-en.pdf Page 6, '9. Electrical Characteristics' section. 'CV charge voltage', MIN:4.21, TYP:4.24,MAX:4.27, that data is normal from you.)
  • 01:54, 30 March 2020 Hansenw talk contribs posted a new comment on X750 (I am charging the X750 and it is at 4.25v and 106%. What is the max charging voltage before I should be concerned?)
  • 09:44, 29 March 2020 Hansenw talk contribs posted a new comment on X750 (Anonymous user #13 is Bill)
  • 09:42, 29 March 2020 24.18.56.157 talk posted a new comment on X750 (I have just finished connecting the X750 to my Raspberry PI 4B and charging the batteries. (via the micro usb on the X750). The script to obtain the battery voltage and % capacity seemed to work fine. However at 100% the battery voltage was 4.24 v and the capacity continued to climb. I stopped it at 102%. Is this an approx. value and this is ok or do I have a problem. Also can I monitor the voltage going to the PI)
  • 23:53, 28 March 2020 73.125.192.210 talk posted a new comment on X725 (How can I detect when the 5v input is off? when the micro USB 5v in power is plugged in I see that the CHG LED turns on, so the board can tell when power is being supplied. Anyway to provide this info to the Raspberry Pi?)
  • 20:08, 28 March 2020 95.86.57.232 talk posted a new comment on LVDS To HDMI Adapter Board (It says it will have any compatibility problem if connected to 4K board! Can you please make the sentence more understandable! Did you teied to say that it wont have any compatibility problem or itis not compatible!)
  • 09:10, 27 March 2020 Cindy talk contribs posted a new comment on X350 (Hello friend, It is powered by the Raspberry Pi, connect the power supply to Raspberry Pi is ok.)
  • 01:24, 27 March 2020 89.245.71.173 talk posted a new comment on WEMOS ESP8266 D1 R2 V2.1 (I have 3 boards. Connected to USB all of them work as expected. power supply via the 9-24VDC Power jack doesn't work. The circuit U2 generates only a voltage of 3.7V (5V expected) regardless of the input voltage. with this low voltage, the ESP only gets 2.6V)
  • 21:03, 26 March 2020 219.78.129.196 talk posted a new comment on X350 (How to connect the power wires?)
  • 17:42, 26 March 2020 Cindy talk contribs posted a new comment on X725 (Hi friend, After install the X725, the poe port of Raspberry Pi has been covered by X735.)
  • 17:35, 26 March 2020 Cindy talk contribs posted a new comment on X856 (Helllo friend, The blue SSD led is used to show the SSD status, the blue led is on indicate that the SSD is running. You can use some opaque tapeto cover it or a back color pen to color it black.(*^_^*))
  • 16:12, 26 March 2020 Harry talk contribs deleted comment #838 on N200
  • 16:12, 26 March 2020 Harry talk contribs deleted comment #840 on Orange Pi
  • 14:34, 26 March 2020 Abby talk contribs posted a new comment on X750 (Hi friend, We receive emails from customers every day Could you please try again? Regards, Geekworm Team)
(newest | oldest) View ( | ) (20 | 50 | 100 | 250 | 500)
Retrieved from "https://wiki.geekworm.com/Special:Log/comments"