Difference between revisions of "X12-A1"
Jump to navigation
Jump to search
| (23 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
{{GD Template Impl}} | {{GD Template Impl}} | ||
| + | |||
| + | ==Safety Instructions & Warnings== | ||
| + | |||
| + | {{UPS Safety Warning}} | ||
| + | |||
==Overview== | ==Overview== | ||
| − | The X12-A1 is a | + | The X12-A1 V1.0 is a stackable battery rack designed to expand the backup power of UPS HAT systems. It uses a parallel configuration of four 18650 batteries, providing plug-and-play battery capacity expansion for compatible UPS HAT systems such as the [[X1209]] (top-mounted) and [[X1203]] (bottom-mounted). Each battery has an independent ultra-low resistance resettable fuse to effectively prevent over-discharge risks; the four parallel XH2.54 connectors support convenient connection and multi-stand stacking, allowing for flexible increases in total power capacity as needed. |
==Features== | ==Features== | ||
| Line 13: | Line 18: | ||
* '''Stacking Design: '''Supports multiple stacks (requires the X12-A1 stacking kit), flexibly expanding total power capacity. | * '''Stacking Design: '''Supports multiple stacks (requires the X12-A1 stacking kit), flexibly expanding total power capacity. | ||
| − | * '''Compatible Models:''' X1209 UPS HAT (top-mounted Raspberry Pi), X1203 UPS HAT (bottom-mounted Raspberry Pi). | + | * '''Compatible Models:''' [[X1209]] UPS HAT (top-mounted Raspberry Pi), [[X1203]] UPS HAT (bottom-mounted Raspberry Pi). |
*'''Core Application: '''The X12-A1 provides a backup battery expansion solution for the aforementioned UPS HATs. | *'''Core Application: '''The X12-A1 provides a backup battery expansion solution for the aforementioned UPS HATs. | ||
| Line 19: | Line 24: | ||
==Technical specification== | ==Technical specification== | ||
{| class="wikitable" | {| class="wikitable" | ||
| + | |||
|- | |- | ||
| − | | ''' | + | | '''Ports & Connectors''' || |
| − | + | XH2.54 2Pin parallel interface x 4 | |
| + | |||
| + | 4-cell 18650 battery socket x1 | ||
|- | |- | ||
| − | | ''' | + | | '''PCB Size''' || |
| − | + | 93.9mm x 77.1mm | |
| − | + | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
|} | |} | ||
==Packing List== | ==Packing List== | ||
| − | * | + | * '''X12-A1 Base Kit''' |
| − | + | ||
| − | + | - X12-A1 18650 battery holder (4-cell parallel) x1 | |
| − | + | ||
| + | - 2-pin 2.54mm pitch male-to-male cable AWG18 30cm x2 | ||
==User Manual== | ==User Manual== | ||
| − | * | + | * X12-A1 Hardware Guide: [https://suptronics.com/Raspberrypi/Power_mgmt/x12-a1-v1.0_hardware.html X12-A1 Hardware] |
| − | + | ||
==FAQ== | ==FAQ== | ||
<!-- 这里提供了一个Q&A的模板，增加Q&A时按照下面的格式写就可以了 --> | <!-- 这里提供了一个Q&A的模板，增加Q&A时按照下面的格式写就可以了 --> | ||
Latest revision as of 17:31, 31 December 2025
Contents
Safety Instructions & Warnings
- It is essential to read and understand these safety instructions and warnings before charging your batteries.
- Lithium Polymer and Li-ion batteries are volatile. Failure to read and follow the instructions below may result in fire, personal injury, and damage to property if charged or used improperly.
- Never make a wrong polarity connection when charging or discharging battery packs. Always double-check the polarity of the battery's connector to ensure that "+" is connected to "+" and "-" is connected to "-".
- Do not mix and use old batteries with new batteries, or batteries with different brand names.
- Lithium batteries have a limited cycle life. Please replace old batteries with new ones when they reach their service life or when they are two years old, whichever comes first.
- When charging the Battery Pack, please place the battery in a fireproof container. Do not leave the UPS shield on wood material or carpet unattended.
- Keep the UPS shield away from children to ensure their safety.
- Ensure your fingers do not touch the solder pads when inserting the battery into the battery holder, as this could cause a short circuit. This is extremely important!!!
- Make sure to insert the battery before turning on the UPS.
- Make sure to insert the battery before connecting the external charger to charge it.
- Please watch Main Video and Tutorial Video regarding 18650 batteries at: https://www.staysafebattery.com/en/
- Battery Recommend for Geekworm UPS board, please refer to: File:NCR18650B.pdf
Overview
The X12-A1 V1.0 is a stackable battery rack designed to expand the backup power of UPS HAT systems. It uses a parallel configuration of four 18650 batteries, providing plug-and-play battery capacity expansion for compatible UPS HAT systems such as the X1209 (top-mounted) and X1203 (bottom-mounted). Each battery has an independent ultra-low resistance resettable fuse to effectively prevent over-discharge risks; the four parallel XH2.54 connectors support convenient connection and multi-stand stacking, allowing for flexible increases in total power capacity as needed.
Features
- Parallel Capacity Expansion: Can accommodate four 18650 batteries connected in parallel, directly increasing power supply capacity.
- Independent Protection: Each battery is equipped with an ultra-low internal resistance resettable fuse to prevent over-discharge.
- Plug and Play: Provides four XH2.54 connectors, compatible with specified UPS HATs, requiring no modifications.
- Stacking Design: Supports multiple stacks (requires the X12-A1 stacking kit), flexibly expanding total power capacity.
- Compatible Models: X1209 UPS HAT (top-mounted Raspberry Pi), X1203 UPS HAT (bottom-mounted Raspberry Pi).
- Core Application: The X12-A1 provides a backup battery expansion solution for the aforementioned UPS HATs.
Technical specification
| Ports & Connectors |
XH2.54 2Pin parallel interface x 4 4-cell 18650 battery socket x1 |
| PCB Size |
93.9mm x 77.1mm |
Packing List
- X12-A1 Base Kit
- X12-A1 18650 battery holder (4-cell parallel) x1
- 2-pin 2.54mm pitch male-to-male cable AWG18 30cm x2
User Manual
- X12-A1 Hardware Guide: X12-A1 Hardware
FAQ
Q1: Question 1
A: Place the answer here.
Enable comment auto-refresher